Free in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style
Sliding glass doors
Impact garage doorsPGTCGI
Before
After
Before
After
Before
AfterCGI Shingle, Tile & Metal Roofing in Fort Pierce: What to Know First
We provide independent CGI shingle, tile & metal roofing installation and repair in Fort Pierce, with most residential jobs completed in one to three days depending on roof size and material. Our pricing runs straight down the middle of the local market: not the cheapest bid you’ll collect, and rarely the highest, but always a line-item quote in writing before the first fastener goes in. If you own a CGI product and need shingle, tile or metal roofing work done right, call (772) 218-5890 and a live person answers.
This page is for Fort Pierce homeowners who already own CGI windows or doors, or are considering them, and want the roofing work around them handled by a crew that understands how the products perform in this climate. We are an independent CGI service provider. We are not affiliated with or authorized by CGI, but we have installed and serviced their lines for years, and we know where they hold up and where they fail.
Key Takeaways
- Most CGI shingle, tile & metal roofing jobs in Fort Pierce run $1,800 to $7,500 for typical residential scopes.
- We register both manufacturer warranty layers in writing before the truck leaves your driveway.
- Every job is covered by our Done Right Promise, with no fine print and no arguing.
- Call (772) 218-5890 for a free estimate. A live person answers, 24/7.
How CGI Products Fail - and How We Fix Them
CGI builds a solid product, but every product has its weak points, and in Fort Pierce the salt air, the summer humidity, and the afternoon thunderstorms find them faster than most places. Here is what we see on CGI shingle, tile & metal roofing jobs along the Treasure Coast, and how we address it.
- Flashing failures around CGI impact windows on tiled roofs. The CGI Estate Collection and Sentry Series are common in Fort Pierce, and both use a heavier frame profile than standard windows. On a tile roof, the flashing where the window meets the roofline takes real abuse. When the flashing is not lapped correctly under the tile, water sneaks behind the frame and into the wall cavity. We pull the affected tile, replace the flashing with the correct setback, and re-bed the tile. The leak stops because we fixed the root cause, not the symptom.
- Shingle granule loss concentrated near CGI window corners. On Fort Pierce homes with CGI windows and architectural shingle roofs, we often see granule loss in a pattern radiating from window corners. The cause is usually wind-driven rain hitting the frame edge and splashing back onto the shingle course below. It is a drainage issue, not a shingle defect. We install a wider drip edge and, where the roof geometry allows, a small diverter that moves the splash away from the shingle surface. The repair looks like it grew there.
- Metal roof oil-canning around CGI curb-mount skylight frames. Metal roofing in Fort Pierce expands and contracts a lot between the January cool snap and the August heat. When CGI skylights or roof windows are mounted on curbs that are too rigid, the metal panel around the curb starts to oil-can, that wavy distortion you can see in the right light. We re-set the curb with expansion joints and re-tension the surrounding panels. The metal lays flat again and stays flat.
- Tile cracking from improper decking beneath CGI roof anchors. Fort Pierce homes with barrel tile or flat tile roofs and CGI impact roof windows sometimes show hairline cracks radiating from the anchor points. The tile was laid over decking that flexes too much, and the anchor transmits that movement. We pull the cracked tile, reinforce the decking around the anchor, and bed the replacement tile properly. You will not see the crack come back, because the decking is no longer moving.
- Weep hole blockages on CGI GardenView and Estate Series windows under tile roofs. Stucco and tile roofs generate dust, and in Fort Pierce the wind pushes that dust straight into window tracks. CGI window frames have weep holes to drain water, but when those holes clog, water pools inside the frame and starts to corrode the hardware from the bottom up. The window still looks fine from the outside until the day it does not open. We clear the weep holes, flush the track channels, and check the internal drainage path with a small bore scope. It is a 20-minute fix that prevents a $600 hardware replacement.
Our CGI Shingle, Tile & Metal Roofing Process
Every CGI roofing job we take in Fort Pierce follows the same sequence. No shortcuts, no surprise line items, and no second appointment left hanging.
- 1
Call and describe the problem. A live person answers at (772) 218-5890. We listen, ask the right questions, and book a visit.
- 2
On-site diagnosis. A background-checked, uniformed technician arrives when we say. We inspect the CGI product, the surrounding roofing, and the transition points where problems usually start.
- 3
Written line-item quote. We put the repair on paper: parts, labor, and the exact scope. We note whether the part is OEM or a quality aftermarket equivalent, and we explain the trade-off. You approve before we start.
- 4
The work. We measure twice, install once, and keep the job site clean. If it is a roofing job around CGI windows or doors, we protect the frames and glass with the same care we would use in our own homes.
- 5
Test and verify. Water test on the flashing, operation test on the window or door, and a visual check of every seam and fastener. If it is not right when the caulk dries, it will not be right in two years either.
- 6
Warranty registration and cleanup. We register both manufacturer warranty layers in writing before the truck leaves the driveway, and we leave the site cleaner than we found it.
What CGI Shingle, Tile & Metal Roofing Costs in Fort Pierce
Here are the numbers we give Fort Pierce homeowners when they ask what a CGI roofing job will cost. These are real ranges from our job history, not guesses.
- Flashing repair around a CGI window or door on a tile roof: $450-$950
- Shingle roof repair with granule loss remediation near CGI frames: $600-$1,400
- Metal roof panel re-tensioning around CGI skylight curbs: $800-$2,200
- Tile replacement with decking reinforcement at CGI anchors: $350-$900 per anchor point
- Full shingle, tile or metal roof install with CGI window integration: $7,500-$24,000 depending on footage and material
What moves the price: the roofing material, the number of CGI window or door transition points, whether we find decking or flashing problems underneath, and whether we use OEM or aftermarket parts. We do not charge for the estimate, and the price on the paper is the price on the bill. Call (772) 218-5890 and we will give you an exact number.
Why Fort Pierce Homeowners Call TruePane Windows & Doors for CGI Work
We have been serving Fort Pierce and the surrounding Treasure Coast since 2008, and Dale Kessler has been at this long enough to know that a roofing job done wrong is a leak waiting for the first hard rain. Our Done Right Promise says it plainly: if it is not done right, we make it right, no paperwork fights and no arguing. The Keystone Standard backs that up, both manufacturer warranty layers registered in writing and durations stated before we leave the job.
We are authorized installers for more than a dozen manufacturer lines, so when a Fort Pierce homeowner wants a side-by-side comparison, we can put CGI next to PGT, CWS, ES Windows, or ECO Window Systems on paper and let them see exactly what they are buying. If the pane is not true, the job is not done. That is not a slogan. It is the rule we work by.
FAQs
As an independent CGI service provider, we work warranty-safe on every job. We never use parts or methods that would void a CGI warranty, and we document the work with photos and written notes so you have a record if the manufacturer ever asks. Call (772) 218-5890 and we will explain exactly how we protect your warranty coverage.
For active leaks or damage that threatens the home, we work you into the schedule as fast as the job before yours allows. Most Fort Pierce customers get an on-site visit within one or two business days. Call (772) 218-5890 and we will give you a straight answer about our current schedule.
We quote both and tell you the difference. For structural components and visible hardware, we recommend OEM. For trim, flashing, and non-structural parts, quality aftermarket equivalents often do the same job for less money. We put both options on paper and let you decide.
If the window frame itself is sound and the problem is flashing, drainage, or surrounding roof material, repair is almost always the smarter money. If the window has water inside the frame or the glass seal has failed, replacement may cost less in the long run. We will show you the condition of what you have and let the numbers speak.
Yes, when the scope requires it, we pull the permit and we pass the inspection. We do the paperwork, we schedule the inspection, and we stand behind the work if the inspector finds anything. Call (772) 218-5890 for a free estimate on your CGI roofing job.
Written by Dale Kessler, Owner, TruePane Windows & Doors at TruePane Windows & Doors, serving Fort Pierce and nearby areas.
Six Reasons Homeowners Choose TruePane Windows & Doors
Impact systems engineered to design pressures up to +/-100, matched to your wind zone - your openings hold when the storm arrives.
Low-E insulated impact glass from our manufacturer lines commonly cuts monthly cooling bills 20-30%.
Laminated impact glass shuts out up to 40% of outside noise - traffic, neighbors, weather.
Monitoring services run $30-90 a month. Laminated impact glass resists forced entry around the clock, with no subscription.
Florida homeowners average around 25% savings on the windstorm portion of their policy after protecting every opening - some homes qualify for more.
A full impact package upgrades curb appeal, buyer confidence and appraised value in one project.