Free in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style
Sliding glass doors
Impact garage doorsPGTCGI
Before
After
Before
After
Before
AfterCGI Door Installation in Fort Pierce: What to Know First
CGI door installation in Fort Pierce typically runs $1,800 to $6,400 depending on the door style, size, and whether you’re replacing an existing CGI unit or putting one in for the first time. We install CGI entry doors, French doors, bifolds, and custom arched units, and most standard single-door jobs are done in one day once the door is on hand. If you own a CGI door and need it set right, or you’re buying one and want it hung by people who understand how these doors behave in coastal Florida, call us at (772) 218-5890 for a straight answer and a free estimate.
How CGI Products Fail - and How We Fix Them
CGI builds a solid impact door. We’ve installed enough of them in Fort Pierce to know exactly where they show strain after ten or fifteen years of salt air and afternoon thunderstorms. Here’s what we see most often.
- Sagging hinges on the Estate Collection entry doors. These are heavy doors, and the factory hinges are good but not immune to twenty years of use. The tell is a door that drags on the threshold on the latch side or a reveal that’s wider at the top than the bottom. We pull the door, re-shim the frame square, and replace hinges with bearing-grade stainless before re-hanging. The door closes like it did the day it was hung.
- Weeping system clogs on CGI sliding glass doors. CGI’s sliders have a weep-and-dam system that moves water out of the track. When Fort Pierce’s fine sand and oak pollen build up in those channels, water pools at the track and starts wicking into the frame. Homeowners think the door is leaking. It’s usually clogged weeps. We clear the channels, check the dam, and re-test with a hose before we call it done.
- Warped or cracked bucks on concrete-block homes. A lot of Fort Pierce homes are CBS construction, and over decades the block settles just enough to throw the rough opening out of square. If the previous installer forced a CGI frame into an out-of-square opening and shimmed it wrong, you’ll see stress cracks at the corners or a deadbolt that stops lining up in July. We re-set the frame properly, which means pulling the door, correcting the opening, and flashing it so water never finds the gap.
- Failed factory weatherstripping on CGI’s older model lines. The original bulb seal CGI used on doors from the early 2000s goes flat after about ten years of Florida sun. You’ll feel a draft at the bottom corners or see daylight around the jamb. We replace with an oversized foam-core seal and compression strip that holds up better than the OEM spec in this climate. It’s a small fix that saves real money in August.
- Roller and track wear on CGI sliding and bifold doors. The rollers CGI uses are decent, but they’re not lifetime parts. When a bifold door starts grinding or a slider takes two hands to move, the rollers are shot. Homeowners sometimes think the whole door needs replacing. It doesn’t. New rollers, a cleaned and straightened track, and that door moves like new for a fraction of replacement cost.
Our CGI Door Installation Process
Here’s how we handle a CGI door installation from first call to final walkthrough, and it’s the same process on a $1,800 entry door or a $6,000 custom arched unit.
- 1
Call and schedule the measure. A live person answers. We set a time, and our tech shows up when we say. He measures the opening twice, checks the existing frame for square and plumb, and notes what’s behind the wall so there are no surprises on install day.
- 2
Parts and warranty decision on paper. We go over your options: OEM CGI parts for exact factory spec, or quality aftermarket where it makes more sense for your budget and the door’s age. You see both numbers before you commit. As an independent CGI service provider, we register every applicable warranty in writing at your address, model and serial number, and the dates that matter. No fine print, no surprises.
- 3
Prep and removal. We protect your floors and remove the existing door without tearing up the rough opening. If the opening is out of square, we correct it with shims and solid blocking, not caulk and hope.
- 4
Installation and flashing. The new CGI door goes in level, plumb, and square. We flash the sill and jambs the way Florida code requires, which is the part that keeps water out of your walls during hurricane season. A bad flashing job is the most common hidden failure we find on other contractors’ work in Fort Pierce.
- 5
Test and prove it. We cycle the door, check the reveals, run water on the sill, and adjust the hardware until the deadbolt throws with one finger. Then we walk you through what we did and register the warranty layers with you standing there.
- 6
Stand behind it. Every job carries our Done Right Promise. If it’s not right when the caulk dries, we come back and make it right without a paperwork fight. Dale Kessler’s rule has been on the whiteboard since day one: if the pane is not true, the job is not done.
What CGI Door Installation Costs in Fort Pierce
Ballpark numbers for common CGI jobs on Treasure Coast homes:
- Single entry door replacement: $1,800 to $3,400 depending on size and whether the frame is sound
- Double French door installation: $3,200 to $5,800 for standard 6-foot or 8-foot openings
- Bifold or folding door: $2,800 to $6,400 depending on panel count and track complexity
- Full frame-out and new CGI door in an existing wall: $3,500 to $6,000 plus any structural work the opening requires
What moves the price: door size, whether we’re reusing the existing frame or setting a new one, custom glass or arch work, and any hidden water damage we find once the old door comes out. If we find something we didn’t expect, we show it to you before we touch it. You’ll never get a surprise line item after the fact. For an exact quote on your door, call (772) 218-5890 and we’ll come measure it free.
Why Fort Pierce Homeowners Call TruePane Windows & Doors for CGI Work
A lot of companies will hang a CGI door. Few of them have been doing this in Fort Pierce long enough to know which houses on Hutchinson Island catch the worst of the salt wind, or why a door set in January behaves differently than one set in August. We have. Dale Kessler grew up off Okeechobee Road and learned the building trade at Indian River State College before spending years doing glass and door work up and down the Treasure Coast. A live person answers our phone 24 hours a day, every day. Our techs are background-checked and uniformed, and they show up in a truck that says TruePane on the side, not an unmarked rental. We’re also authorized installers for more than a dozen other lines, and PGT among them, so if a CGI door isn’t the right call for your opening, we’ll say so and show you side-by-side numbers on paper. And if it is not right when the caulk dries, it will not be right in two years either. That’s why we fix it now, under our Done Right Promise.
FAQs
No, not if the installation is done correctly and the warranty is registered properly. The bigger risk is a bad install that causes water intrusion or frame stress, which CGI’s warranty won’t cover because it’s an installation issue, not a manufacturing defect. We register both warranty layers, manufacturer and workmanship, in writing before our truck leaves your driveway. That’s The Keystone Standard on every job.
A standard single-door CGI installation takes one day once the door is on hand. Custom orders from CGI run anywhere from two to six weeks depending on the door’s size, finish, and glass package. We give you a written timeline at the measure and stick to it. Call (772) 218-5890 and we’ll tell you what your specific door’s lead time looks like right now.
It depends on the door and what’s actually wrong with it. For structural components, hinges, strike plates, threshold systems, we prefer OEM CGI parts so the door keeps its rating and its warranty. For consumable parts like weatherstripping and rollers, quality aftermarket often outperforms the factory spec in Florida’s climate, and we’ll show you both options on paper. The decision is always yours, with the prices in front of you before we start.
In most cases, yes. A dragging door, a sticking lock, a leaking threshold, or a slider that won’t roll is usually a repair, not a replacement, and we’ll tell you that honestly even when a replacement would make us more money. If the frame is rotted, the door skin is cracked through, or the impact rating has been compromised, replacement is the only safe call. We’ll show you the evidence before you spend a dollar.
We’re an independent CGI service provider. We install and service CGI doors every month, and we know their product lines well, but we’re not affiliated with or authorized by CGI. That’s actually good for you. We have no reason to push a CGI part over a better aftermarket option when it makes sense, and we tell you the truth either way.
If you’ve got a CGI door that needs installing in Fort Pierce, or one that’s been giving you trouble since the last contractor left, call us at (772) 218-5890. We’ll come look, give you a straight number, and if we do the work, we’ll stand behind it in writing.
Written by Dale Kessler, Owner, TruePane Windows & Doors at TruePane Windows & Doors, serving Fort Pierce and nearby areas.
Six Reasons Homeowners Choose TruePane Windows & Doors
Impact systems engineered to design pressures up to +/-100, matched to your wind zone - your openings hold when the storm arrives.
Low-E insulated impact glass from our manufacturer lines commonly cuts monthly cooling bills 20-30%.
Laminated impact glass shuts out up to 40% of outside noise - traffic, neighbors, weather.
Monitoring services run $30-90 a month. Laminated impact glass resists forced entry around the clock, with no subscription.
Florida homeowners average around 25% savings on the windstorm portion of their policy after protecting every opening - some homes qualify for more.
A full impact package upgrades curb appeal, buyer confidence and appraised value in one project.